| The time now is Jul 24, 2008 - 02:59 AM |
No Commercial Advertising Allowed On The Forums - Please use the Directory or Classifieds. If you're a friend of the community and have added value to the forum, please feel free to share with us...if you're only trying to push a product, it will be deleted.
 |
 |
|
|
| Author |
Message |
|
|
Post subject:bending aluminum sheetmetal 180 degrees
 Posted: Apr 06, 2008 - 02:03 AM #7467
|
|
Joined: Apr 05, 2008
Posts: 2
|
|
| im trying to make a die to bend a 6 inch square .08 thick aluminum 180degrees and the piece will have a 1.5inch radius, i need to make a few thousand of these parts that is why im building a die, im a machinist but have no die experience, anyone have experience doing something like this? any links? im not sure what radius i need to make the die, thanks for any help. |
|
|
| |
|
|
|
 |
|
|
|
Post subject:RE: bending aluminum sheetmetal 180 degrees
Posted: Apr 07, 2008 - 07:14 PM #7477
|
|
Joined: Apr 05, 2008
Posts: 2
|
|
| wow lots of views, no ideas? |
|
|
| |
|
|
|
|
|
|
|
Post subject:RE: bending aluminum sheetmetal 180 degrees
Posted: Apr 08, 2008 - 01:33 AM #7480
|
|
Power User
Joined: Nov 13, 2007
Posts: 112
Location: Omaha, NE
|
|
| I don't understand the question. Perhaps with a picture? |
_________________
----------------------
Go Huskers!
|
| |
|
|
|
|
|
|
|
Post subject:RE: bending aluminum sheetmetal 180 degrees
Posted: Apr 08, 2008 - 02:18 PM #7484
|
|
Joined: Nov 08, 2005
Posts: 12
Location: Gastonia, NC
|
|
I used to do stuff like this, although kind of crudely, and with lots of experimentation. The radius will be determined by the radius of the
punch (top die) if you are air bending...my preference over compression bending. You must allow for springback, which is affected by both alloy
and grain direction. The punch should be thermometer shaped to allow
bending past 180 degrees to compensate for springback.
The bottom die will have two hinged sections, that narrow the top opening
when the thermometer part reaches the bottom extent of its travel. This
narrowing gives you the over 180 degrees that you need to compensate
for springback. The aluminum may not follow the radius of the punch,
especially if you're bending across the grain, so try to keep the stroke short, otherwise, you'll end up with something that looks like you bent it over your knee.
A guide is also necessary to make sure to bend in the center. Any error is doubled.
I just had a flash....talk to someone who makes urethane bottom dies and holders. They might come up with something a lot simpler than a hinged
bottom die. |
|
|
| |
|
|
|
|
|
|
|
Post subject:RE: bending aluminum sheetmetal 180 degrees
Posted: May 20, 2008 - 09:09 PM #7599
|
|
Joined: Mar 10, 2008
Posts: 16
|
|
| inside radius or outside radius ?? what tolerance ?? say inside radius of 1.5" + or - .016" punch to be 1.469 radius and the bolster to be 1.549, footnote I am using English inches I hope your inches are similar |
|
|
| |
|
|
|
|
|
|
|
All times are GMT - 6 Hours
|
|
|
|
|
|
|
Templates designed by Pete Ottery - Theme designed by Sound Web Development
|
